Pull Schedule

Archives
Log in
Subscribe
October 8, 2026

Imagineering at home: I'm becoming the Black Pearl

A black 3D-printed cannon on a cluttered desk, its muzzle ring glowing white with a puff of mist rising out of it

A test cannon on my desk, mid-shot.

My son is going as Captain Jack Sparrow this year. So I'm not going as a pirate. I'm going as the ship.

I'm building the Black Pearl. A wearable one: a cardboard hull on shoulder straps, so I wear the whole ship and he sails along beside me. It's the part of the job I don't get to do on a paid install. Pure Imagineering, in my own garage, for an audience of one.

The cannons

There are eight 3D-printed cannons, four down each side of the hull. Each one has a WS2812 LED ring in the muzzle. It's addressable RGB, so every cannon can do its own thing. A single cannon firing runs a little sequence I'm proud of.

First the fuse "lights": the ring crackles in orange and yellow, flickering like a lit fuse burning down. It builds until the whole ring is a solid orange glow. Then it snaps to a bright white flash, and that flash is the moment the smoke comes out, for about a second and a half. Then the white settles into a hot red-and-orange glow, and the embers fade away around the ring until it's dark again. Fuse, flash, smoke, embers.

A black cannon on a desk: its muzzle ring flickers orange, flashes white as a puff of mist rises, then glows red and fades to dark

One cannon running the full firing sequence.

The smoke is the part people always ask about. Each cannon is fully self-contained. It has its own water reservoir holding about 40 milliliters, enough to keep the wick wet for a couple hours of trick-or-treating, and its own ultrasonic atomizer disc sitting about an inch and a half behind the LED ring, up inside the barrel. The disc comes out of a cheap humidifier atomizer kit. Everything around it I'm building.

Exploded-view drawing of one cannon, labeled: spring, wick, fill plug, cannon board, breech cartridge, atomizer disc, bay door, port plate, barrel, LED ring and muzzle liner

One cannon, from my assembly guide.

Looking down the barrel of a cannon at a ring of 12 small LEDs around the muzzle opening

The LED ring, seated in the muzzle.

Each cannon needs five signals: two for the mister, and three for the LED ring (power, ground and data). They run over an ordinary Cat5e patch cable with RJ45 plugs on both ends. The mister drive swings tens of volts at about 120 kHz, so it gets a twisted pair to itself, and the spare conductors double up the power and ground. That makes the cannons easy to fire independently, and easy to swap if one gets crushed on a driveway. It isn't Ethernet, though, and the boards say NOT ETHERNET next to the jacks so nobody plugs a cannon into a network switch.

Two brains, one for each side

The brains are two boards I designed myself, one for port and one for starboard. Each one takes an ESP32 dev board in female headers, a DFRobot DFPlayer Mini for sound, and the drivers for four cannons. Each side runs off its own USB-C power bank, and the two sides talk to each other wirelessly over ESP-NOW. So instead of a rat's nest of modules hot-glued to the inside of the hull, each side is one board doing light, mist and audio.

I've ordered both brain boards from JLCPCB, along with a small RJ45 breakout board for each cannon.

Wiring diagram titled Black Pearl Cannons, how everything is wired: a port and a starboard brain board, each with an ESP32, a DFPlayer Mini, a speaker, a USB-C power bank and four cannons on patch cables, linked by ESP-NOW, with a pin-by-pin table for one cannon

How it all wires up. Tap for full size.

Render of a green circuit board with four jacks labeled Cannon 1 to 4 and Not Ethernet, a speaker terminal, and sockets for the ESP32 and MP3 board

A render of one brain board. The real ones are on order.

It has an app, because of course it does

I built an app to control the cannons. I can fire one cannon, fire a whole side, fire everything at once, or run a volley down the line. Or I set it to run an automated show and just let it go off on its own while I hand out candy.

An ESP32 board wired with yellow jumpers to a clear breadboard, with a red and black lead running to a mist atomizer, on a wooden desk

The breadboard version, before the boards.

There will be sound, too, though it isn't working yet. One speaker per side, driven by the DFPlayer. Cannon booms when they fire. And underneath it all, an ambient bed of a ship creaking on the water, with a certain famous line about dead men and the tales they don't tell dropping in between shots. Every clip will be free and royalty-free, and that famous line will be a re-recorded royalty-free soundbite, not the movie audio.

Ghost ship mode

This is the one I can't wait to see on a dark street. In ghost ship mode, every cannon ring stops being fire and goes cold. The LEDs flicker and glow in aqua green and dark blue, slow and creepy, like the Pearl rising up out of the water. And instead of sharp cannon puffs, the misters breathe out gently at different rates, so a low fog pools around the whole hull.

What's left

The boards are on order. When they arrive, they get built up and the sound goes in. If I get all of that done and working, the stretch goal is some lighting on the outside of the ship to make the hull read better at night.

Halloween is the deadline that doesn't move. If a cannon's misfiring on the 30th, that's a problem for the 30th. Either way, he's getting his ship. I'll post photos after.


Read this on the web · You're getting this because you subscribed to Pull Schedule.

Don't miss what's next. Subscribe to Pull Schedule:
← Newer The 12V trigger board I built for my own amps Older → The star ceiling I built, and the one I'm building now
Powered by Buttondown, the easiest way to start and grow your newsletter.